HS2 fuel overflow
Created by: onetim
Orig. Posting Date | User Name | Edit Date |
Jun 5, 2018 04:37AM | onetim | |
Jun 3, 2018 07:18AM | dklawson | |
Jun 2, 2018 07:05PM | onetim | Edited: Jun 2, 2018 07:10PM |
Jun 1, 2018 07:22PM | 1963SV2 | |
Jun 1, 2018 05:14PM | onetim | |
May 31, 2018 03:06PM | dklawson | |
May 31, 2018 12:06PM | malsal | Edited: Jun 1, 2018 04:49AM |
May 31, 2018 08:44AM | onetim |
Found 28 Messages
Total posts: 1007
Last post: Jul 19, 2022 Member since:Jul 24, 2014
|
Cars in Garage: 0
Photos: 0 WorkBench Posts: 0 |
Total posts: 9241
Last post: Aug 17, 2023 Member since:Jun 5, 2000
|
Cars in Garage: 0
Photos: 0 WorkBench Posts: 0 |
|
In an earlier post you said that the float bowls were both about 1/2 full. Have you checked the bowl level immediately after the overflow occurs? Can you post pictures of your carb plumbing?
Doug L.
Total posts: 1007
Last post: Jul 19, 2022 Member since:Jul 24, 2014
|
Cars in Garage: 0
Photos: 0 WorkBench Posts: 0 |
So I did the needle seal test, seals perfectly, thinking that the white plastic floats drop too far down into the float bowls when they are empty, binding the needle with no means of adjusting. This has nothing to do with float level, or the upper shutoff level, which can be adjusted and appears to be correct. So the car is working fine now no pissing at the moment. I see our hosts sells phenolic black floats with metal tabs, but I would like to buy some good old brass ones if anyone has some.
Total posts: 1716
Last post: Oct 18, 2020 Member since:Oct 18, 2011
|
Cars in Garage: 0
Photos: 0 WorkBench Posts: 0 |
In the carbs I have (I think it works for all plastic floats) the fuel level is controlled by shims/gaskets under the seat. If you've carefully inspected the needle tip (actually about a sixteenth or so from the tip) for damage/ridges I would be removing the seats and checking that the shims/gaskets are OK and that the seats are secured properly in the lid....
You can test the integrity of the needle and its seat by removing the lid, installing the needle and holding it in place with light finger pressure. With the lid the right way up blow into the intake. If there's a leak you will hear it. By reducing your finger pressure you will be able replicate the fuel pressure allowing fuel past the seat while a little more pressure will stop it. (Well the pressure doesn't actually blow the needle off its seat rather the falling fuel level in the bowl allows the float and the needle sitting on it to fall down under gravity...)
It doesn't take much finger pressure to block a fair bit of lung power.
Cheers, Ian
You can test the integrity of the needle and its seat by removing the lid, installing the needle and holding it in place with light finger pressure. With the lid the right way up blow into the intake. If there's a leak you will hear it. By reducing your finger pressure you will be able replicate the fuel pressure allowing fuel past the seat while a little more pressure will stop it. (Well the pressure doesn't actually blow the needle off its seat rather the falling fuel level in the bowl allows the float and the needle sitting on it to fall down under gravity...)
It doesn't take much finger pressure to block a fair bit of lung power.
Cheers, Ian
Total posts: 1007
Last post: Jul 19, 2022 Member since:Jul 24, 2014
|
Cars in Garage: 0
Photos: 0 WorkBench Posts: 0 |
Well, A bit of an update, pulled apart both float bowls, cleaned, polished the four slide faces on the needles, they are brass with neoprene tips. Fuel level looked even in both bowls, a little over half full. Has plastic floats that look dry inside. Put it all back together, started it up and it pissed gas all over the floor like a scared puppy. Same carb overflowing as before. I see the plastic floats have a non bendable stop tab for how low it allows them to drop into the bowl. Looks a bit excessive to where it could possibly hang up on the bowl wall. Thoughts, ideas? I could test this by putting in an approximately correct amount of fuel in the bowl, then see if it stops overflowing. This would explain only having the problem the first run of the year. But then what, file the edge of the float, buy a different kind? Thanks again
Total posts: 9241
Last post: Aug 17, 2023 Member since:Jun 5, 2000
|
Cars in Garage: 0
Photos: 0 WorkBench Posts: 0 |
|
Everyone has an opinion about Grose jets. I have used them. I won't anymore. I have had them stick open and I've had them stick closed. If you decide to use them, wash them first with a liberal amount of spray carb cleaner. The units are shipped with a Cosmoline like coating to prevent the steel balls from corroding while in storage. That coating needs to be removed prior to installing the jets.
Doug L.
Total posts: 8382
Last post: Jan 13, 2022 Member since:Feb 7, 2006
|
Cars in Garage: 0
Photos: 0 WorkBench Posts: 0 |
|
Quote:
Originally Posted by onetim
Hi all, I have had a fuel overflow problem on my left HS2 right from the start after a rebuild. The first time just a tap on the bowl fixed the issue for the season, same thing the next year, this year, ah, not so good. No problem at first, then loaded up on a short drive, and cleared out, signs of fuel having leaked out of overflow tube. Ok no big deal, will change needle and seat, check for smooth operation. but I see for sale a Grous jet, is it better, or just change out with stock neoprene. I do have a clean looking filter at the firewall, And I don't think its all a crud problem, as this started from the rebuild. Thank's for your insight.
The grose jets seem to work well as do the viton ones with the rubber tip
If in doubt, flat out. Colin Mc Rae MBE 1968-2007.
Give a car more power and it goes faster on the straights,
make a car lighter and it's faster everywhere. Colin Chapman.
Total posts: 1007
Last post: Jul 19, 2022 Member since:Jul 24, 2014
|
Cars in Garage: 0
Photos: 0 WorkBench Posts: 0 |
Hi all, I have had a fuel overflow problem on my left HS2 right from the start after a rebuild. The first time just a tap on the bowl fixed the issue for the season, same thing the next year, this year, ah, not so good. No problem at first, then loaded up on a short drive, and cleared out, signs of fuel having leaked out of overflow tube. Ok no big deal, will change needle and seat, check for smooth operation. but I see for sale a Grous jet, is it better, or just change out with stock neoprene. I do have a clean looking filter at the firewall, And I don't think its all a crud problem, as this started from the rebuild. Thank's for your insight.
Found 28 Messages